in force 2026-05-29 INSERTED+5,831 −0§
Amended by Regulation (EU) 2024/2748 32024R2748
applies from: unknown (an inserted provision states its own application date only in prose)
Sources disagree — the text comparison and the amending act's instructions found this change; the EU's own amendment metadata does not list it. All are shown; none is overruled.
This is a newly inserted article allowing a Member State to authorise, on a duly justified request from an economic operator, the placing on the market or putting into service of specific machinery or related products for which mandatory notified-body conformity assessment procedures were not carried out but for which compliance with the applicable essential health and safety requirements has been demonstrated by other means.
The provision sets out related mechanisms including Commission notification and possible extension of the authorisation's validity across the Union, urgency procedures for adopting implementing acts, conditions such as an end date tied to activation of the internal market emergency mode, exemption from CE marking, and market surveillance powers, all attached to this newly added text.
Cited: Art. 25c, v2
text before / after
inserted text (02023R1230-20260529)
Article 25c Derogation from conformity assessment procedures requiring the mandatory involvement of a notified body 1. By way of derogation from Article 25, a Member State may authorise, on a duly justified request from an economic operator, the placing on the market or putting into service within the territory of that Member State, of specific machinery or related products listed in the implementing act referred to in Article 25a(1) and for which the conformity assessment procedures referred to in Article 25 that require the mandatory involvement of a notified body have not been carried out but for which the compliance with all the applicable essential health and safety requirements set out in Annex III has been demonstrated in accordance with procedures referred to in that authorisation. 2. The Member State shall immediately inform the Commission and the other Member States of any authorisation granted in accordance with paragraph 1 of this Article. Provided that the requirements set out in the authorisation ensure conformity with the applicable essential health and safety requirements laid down in Annex III, the Commission shall adopt, without delay, an implementing act extending for a limited period of time the validity of the authorisation granted by a Member State in accordance with paragraph 1 of this Article to the territory of the whole Union and shall set out the conditions under which the specific machinery or related products may be placed on the market or put into service. When preparing the draft implementing act, the Commission may request national market surveillance authorities to provide relevant information or comments regarding the technical assessment that served as the basis for the authorisation referred to in paragraph 1 of this Article. The implementing act shall be adopted in accordance with the examination procedure referred to in Article 48(3). The machinery or related products subject to the extension of validity referred to in the first subparagraph shall bear the information that they are placed on the market or put into service as a crisis-relevant good. The implementing act referred to in the first subparagraph shall specify the content and presentation of that information. That information, as well as any labelling, shall be clear, understandable and intelligible and, where relevant, in a language which can be easily understood by consumers and other end-users, as determined by the Member State concerned. 3. On duly justified imperative grounds of urgency relating to the need to preserve the health and safety of persons, the Commission shall adopt immediately applicable implementing acts in accordance with the procedure referred to in Article 48(4). 4. As long as an implementing act as referred to in paragraph 2 or 3 is not adopted, the authorisation granted by a competent national authority in one Member State shall be valid only on the territory of that Member State, and on the territories of any other Member States whose competent national authorities have recognised the validity of that authorisation before the adoption of such an implementing act. Member States shall inform the Commission and the other Member States of any decision to recognise the validity of that authorisation. 5. Manufacturers of machinery or of related products subject to the authorisation procedure referred to in paragraph 1 shall declare on their sole responsibility that the machinery or the related products concerned comply with all the applicable essential health and safety requirements set out in Annex III and shall be responsible for the fulfilment of all the conformity assessment procedures indicated by the competent national authority. 6. Any authorisation issued pursuant to paragraph 1 shall set out the conditions and requirements under which the machinery or the related products may be placed on the market or put into service. Such authorisations shall set out at least the following: (a) a description of the procedures by means of which compliance with the applicable essential health and safety requirements set out in Annex III to this Regulation was successfully demonstrated; (b) any specific requirements regarding the traceability of the machinery and the related products concerned; (c) an end date of validity of the authorisation, which cannot go beyond the last day of the period for which the internal market emergency mode has been activated in accordance with Article 18 of Regulation (EU) 2024/2747; (d) any specific requirements regarding the need to ensure a continuous conformity assessment with respect to the machinery and the related products concerned; (e) measures to be taken upon expiry or deactivation of the internal market emergency mode with respect to the machinery or the related products concerned that have been placed on the market or put into service. 7. By way of derogation from Articles 4, 23 and 24, machinery or related products for which an authorisation has been granted in accordance with paragraph 1 of this Article shall not bear the CE marking and Article 4 shall not apply. 8. The market surveillance authorities of a Member State where an authorisation pursuant to paragraphs 1, 2 and 4 of this Article is valid shall be entitled, with respect to such machinery and related products, to take all corrective and restrictive actions at national level provided for under Regulation (EU) 2019/1020 and under this Regulation. They shall immediately inform the Commission and the market surveillance authorities of all other Member States of these actions. 9. The use of the authorisation procedure set out in paragraphs 1 to 4 of this Article shall not affect the application on the territory of the Member State concerned of the relevant conformity assessment procedures laid down in Article 25.